It is pretty normal to get Linksys AC2200 Velop router keeps disconnecting issue. But, you don’t have to worry! Luckily, you are on the right post. Here, you will find the most effective Linksys Velop troubleshooting tips that will help you fix the issue in a jiffy. Continue reading!
Solved: Linksys AC2200 Keeps Disconnecting
Fix 1
Move Your AC2200 Closer to Modem
One of the major reasons why you are getting the “Linksys AC2200 Velop router keeps disconnecting” issue is because it is placed away from the reach of your existing modem. To do away with the problem, make sure that your Velop device and modem are placed in close proximity.
Once done, access Linksys Velop router login page to see if the issue is fixed or not.
Still, getting “Linksys AC2200 Velop router keeps disconnecting” issue? No worries! Just ensure that the Ethernet connection between the devices is stable. On the off chance that the Ethernet cable connecting your Velop device and the existing modem is worn out or damaged, get it replaced immediately with a new one.
Note: Your devices can also be connected using a wireless source.
Fix 2
Keep WiFi Signal Interference at Bay
Chances are that the signals of your Linksys Velop router are getting interrupted because of WiFi devices, electronic appliances, and metal objects.
Therefore, make sure to place your Linksys Velop away from Bluetooth speakers, microwave Owens, baby monitors, gaming consoles, reflexive surfaces, cordless phones, etc.
If you are still facing “Linksys AC2200 Velop router keeps disconnecting” issue, then perhaps you should consider updating its firmware version.
Fix 3
Perform Linksys Velop Firmware Update
Given below are the instructions that you must follow in order to update the firmware of your Linksys Velop router to the latest version:
Step 1: Connect your Linksys Velop router and modem properly.
Step 2: Turn on your computer or laptop and launch an internet browser of your choice in it.
Step 3: In the address bar of the internet browser, type the default IP of your Linksys Velop device.
Step 4: The Linksys Velop login page will appear on your device screen.
Step 5: Enter the default username and password of your Linksys Velop.
Step 6: Follow the on-screen instructions and you will be able to update the firmware of your Linksys Velop in the blink of an eye.
Fix 4
Contact Your ISP
If you are still struggling with “Linksys AC2200 Velop router keeps disconnecting” issue, it’s probably because of a weak or poor internet connection.
Thus, getting in touch with your internet service provider might help you to fix the issue.
Still No Luck?
Argh! Still, experiencing “Linksys AC2200 Velop router keeps disconnecting” issue? Don’t sweat over it! Resetting your Linksys Velop is the only option you are left with.
Fix 5
Reset Your Linksys AC200 Velop
Here’s how to reset your Linksys AC2200 Velop back to factory default values:
Step 1: Make sure that your Linksys AC2200 Velop router is powered on and gets a steady power supply.
Step 2: Disconnect your Velop device and existing modem.
Step 3: Locate the reset hole on your Linksys AC2200 Velop router.
Step 4: Press the AC2200 reset hole using a toothpick, oil pin, or a paper clip.
Step 5: Hold the reset hole and a few moments later, release it.
As soon as you are done resetting your Velop router, perform the Linksys AC2200 setup process again.
In a Nutshell
To get blazing-fast internet in every nook and cranny of your house, it is important to perform Linksys AC2200 set up in a proper way. However, if you get “Linksys AC2200 Velop router keeps disconnecting” issue, again and again, consider following the hacks provided in this article. By following these hacks, you will surely be going to make the most out of your Linksys Velop WiFi. Just stay connected to it.
Before we end this article, there is one more hack that we would like to share with you. Keep power cycling or restarting your Linksys AC2200 Velop router once in a month. Doing so will ensure the smooth and proper functioning of your Linksys Velop router.
Wish you all the best and happy streaming with Linksys AC2200 Velop router!
